ZT Loader-Excavator — One Chassis, Two Working Ends, for Sites a Full-Size Excavator Cannot Enter
A wheeled loader-excavator built for contractors who excavate, load and backfill on the same site. The front loading bucket and the rear digging arm share one chassis, so the operator changes task without changing machine. We configure each unit against the buyer's ground conditions and duty cycle — that is what 20+ years as a loader manufacturer exporting Chinese construction machinery actually changes.
Three Site Problems This Machine Is Specified Around
Ground harder than the bucket is rated for. 50 ±10% kN digging force at the rear bucket, >40 kN breakout force at the front. The operator breaks the surface with the backhoe, then moves spoil with the 1 m³ loader bucket — one machine, one pass.
Sites too tight to turn. 4,300 mm minimum turning radius against a 2,730 mm body width, with a 180° digging bucket swing, so a trench can be cut parallel to a wall and spoil swung to either side without repositioning the chassis.
Shifts longer than the fuel stop. 100 L diesel and 155 L hydraulic capacity, >30° grade ability and 70–75 kN traction on unpaved haul roads. 500 mm ground clearance protects the underside on rutted ground.
What Two Decades of Export Changes About the Order
Configuration is fixed before deposit. Bucket size, tyre spec and attachment set are matched to the buyer's ground and typical job, not left at default export spec.
Wear parts ship with the machine. A recommended kit — bucket teeth, hydraulic hoses, filters — is quoted alongside so the first service interval does not wait on an international parcel.
One team owns the shipment. Export packing, container loading plan and customs documents are handled in-house by the same team that quoted the unit.
No trading layer in the price. We quote as the manufacturer, so the factory price carries your specified configuration and export packing without an intermediary margin.
Buyers adding heavy equipment components — buckets, cylinders, seals, filters — consolidate them into the same container, which on a single-unit order usually decides whether the landed cost works.
Nine Job Types
Construction — foundation digging and material handling
Agriculture — orchard clearance, channel digging, dredging
Municipal projects — night trenching and reinstatement
Mining — narrow tunnel clean-up and material transfer
Pipeline laying — controlled trench width and depth
Emergency rescue — flood debris and access clearing
Forestry — debris removal alongside trimming
Ranch maintenance — manure and bedding clean-out
Snow removal — clearing and stacking in one movement
Technical Specifications
| Item | Unit | Parameter |
|---|---|---|
| Backhoe bucket capacity 挖斗容积 | m³ | 0.3 |
| Rated loading bucket capacity 铲斗容积 | m³ | 1 |
| Rated lifting force 额定举升力 | kN | >25 |
| Equipment weight 整机重量 | kg | 7840 |
| Backhoe parameters 挖掘端参数 | Max. digging radius 最大挖掘半径 (mm) | 5481 |
| Max. dump height 最大挖掘高度 (mm) | 3737 | |
| Radius at max. dump height 最大卸载半径 (mm) | 1084 | |
| Max. digging radius at ground level 最大水平挖掘半径 (mm) | 5105 | |
| Digging bucket max. rotating angle 最大挖掘旋转角度 (°) | 180 | |
| Max. digging depth 最大挖掘深度 (mm) | 4340 | |
| Max. digging force 最大挖掘力 (kN) | 50±10% | |
| Loading parameters 装载端参数 | Max. dump height 最大卸载高度 (mm) | 2626 |
| Dump reach at max. dump height 最大卸载距离 (mm) | 726 | |
| Bucket draw back angle — transportation position 仰角 (°) | 43.5 | |
| Bucket draw back angle — ground position 收斗角 (°) | 36.5 | |
| Dump angle 倾倒角 (°) | 43.5 | |
| Digging depth 挖掘深度 (mm) | 191 | |
| Max. breakout force 最大掘起力 (kN) | >40 | |
| Max. grade ability 最大爬坡能力 | ° | >30 |
| Max. traction power 最大牵引力 | kN | 70–75 |
| Min. turning radius 最小转弯半径 | mm | 4300 |
| Wheelbase 轴距 | mm | 2320 |
| Front wheel track 前轮距 | mm | 1910 |
| Rear wheel track 后轮距 | mm | 1820 |
| Minimum ground clearance 最小离地间隙 | mm | 500 |
| Total length 长度 | mm | 7100 |
| Total height (cab) 高度（驾驶室） | mm | 2870 |
| Total width 宽度 | mm | 2730 |
| Bucket width 斗宽 | mm | 2300 |
| Digging end bucket width 挖斗宽度 | mm | 750 |
| Hydraulic tank 液压油箱 | L | 155 |
| Diesel tank 柴油箱 | L | 100 |
| Tire 轮胎 | 14-17.5 | 19.5L-24 |
| Voltage 电压 | V | 12 |
| Engine 发动机 | — | Cummins 75 kW |
Manufacturing process certified to ISO.
Frequently Asked Questions
Can the machine be configured differently from the standard export spec?
Yes. Bucket, tyre and attachment choices are settled before the deposit, based on the ground you work and the job you run most often. Send those two details and we return a written configuration list for your approval.
What happens after I place the order?
You receive the configuration list, a production schedule, and the container loading plan for sign-off. The same team that quoted the unit handles export packing and customs documents through to the port.
Are spare parts supplied with the first order?
A recommended wear-parts kit is quoted alongside the machine so the first service interval does not wait on an international parcel. Buyers can add further components to the same shipment.
What documentation ships with the machine?
Operation and maintenance manual, parts catalogue, and the export documentation set — packing list, commercial invoice and certificate of origin.
How do I get a price for my destination?
Send the destination port and the configuration you need. The reply is a factory price for that specification, with export packing included and no intermediary margin added.
Detailed Photos
Packaging & Shipping
Two units load into one 40HQ container. Loading plans, lashing points and export packing are confirmed before the unit leaves the factory.
Request a Configuration Quote
Send ground conditions, typical trench or pit dimensions, and site access width. WhatsApp: +86 139 5387 9973
